Cesar C. Salazar Gonzalez
Master
Registrado: 01 Oct 2002Mensajes: 2155Ubicación: San Cristóbal de Las Casas, Chiapas
|
 Publicado: Jue 26 Jun, 2003 9:54 pm Asunto: Ayuda con la siguiente funcion, (detecta serial de HD) |
 |
|
Hola, les pido ayud para, que me indique como convertir la siguiente funcion para builder, ya que no me se ejecuta muy bien..
| Código: |
// diskid32.cpp
// for displaying the details of hard drives in
// 06/11/2000 Lynn McGuire written with many contributions from others,
// IDE drives only under Windows NT/2K and 9X,
// maybe SCSI drives later
#define PRINTING_TO_CONSOLE_ALLOWED
#include <stdlib.h>
#include <stdio.h>
#include <windows.h>
// Required to ensure correct PhysicalDrive IOCTL structure setup
#pragma pack(1)
// Max number of drives assuming primary/secondary, master/slave topology
#define MAX_IDE_DRIVES 4
#define IDENTIFY_BUFFER_SIZE 512
// IOCTL commands
#define DFP_GET_VERSION 0x00074080
#define DFP_SEND_DRIVE_COMMAND 0x0007c084
#define DFP_RECEIVE_DRIVE_DATA 0x0007c088
#define FILE_DEVICE_SCSI 0x0000001b
#define IOCTL_SCSI_MINIPORT_IDENTIFY ((FILE_DEVICE_SCSI << 16) + 0x0501)
#define IOCTL_SCSI_MINIPORT 0x0004D008 // see NTDDSCSI.H for definition
// GETVERSIONOUTPARAMS contains the data returned from the
// Get Driver Version function.
typedef struct _GETVERSIONOUTPARAMS
{
BYTE bVersion; // Binary driver version.
BYTE bRevision; // Binary driver revision.
BYTE bReserved; // Not used.
BYTE bIDEDeviceMap; // Bit map of IDE devices.
DWORD fCapabilities; // Bit mask of driver capabilities.
DWORD dwReserved[4]; // For future use.
} GETVERSIONOUTPARAMS, *PGETVERSIONOUTPARAMS, *LPGETVERSIONOUTPARAMS;
// Bits returned in the fCapabilities member of GETVERSIONOUTPARAMS
#define CAP_IDE_ID_FUNCTION 1 // ATA ID command supported
#define CAP_IDE_ATAPI_ID 2 // ATAPI ID command supported
#define CAP_IDE_EXECUTE_SMART_FUNCTION 4 // SMART commannds supported
// IDE registers
typedef struct _IDEREGS
{
BYTE bFeaturesReg; // Used for specifying SMART "commands".
BYTE bSectorCountReg; // IDE sector count register
BYTE bSectorNumberReg; // IDE sector number register
BYTE bCylLowReg; // IDE low order cylinder value
BYTE bCylHighReg; // IDE high order cylinder value
BYTE bDriveHeadReg; // IDE drive/head register
BYTE bCommandReg; // Actual IDE command.
BYTE bReserved; // reserved for future use. Must be zero.
} IDEREGS, *PIDEREGS, *LPIDEREGS;
// SENDCMDINPARAMS contains the input parameters for the
// Send Command to Drive function.
typedef struct _SENDCMDINPARAMS
{
DWORD cBufferSize; // Buffer size in bytes
IDEREGS irDriveRegs; // Structure with drive register values.
BYTE bDriveNumber; // Physical drive number to send
// command to (0,1,2,3).
BYTE bReserved[3]; // Reserved for future expansion.
DWORD dwReserved[4]; // For future use.
BYTE bBuffer[1]; // Input buffer.
} SENDCMDINPARAMS, *PSENDCMDINPARAMS, *LPSENDCMDINPARAMS;
// Valid values for the bCommandReg member of IDEREGS.
#define IDE_ATAPI_IDENTIFY 0xA1 // Returns ID sector for ATAPI.
#define IDE_ATA_IDENTIFY 0xEC // Returns ID sector for ATA.
// Status returned from driver
typedef struct _DRIVERSTATUS
{
BYTE bDriverError; // Error code from driver, or 0 if no error.
BYTE bIDEStatus; // Contents of IDE Error register.
// Only valid when bDriverError is SMART_IDE_ERROR.
BYTE bReserved[2]; // Reserved for future expansion.
DWORD dwReserved[2]; // Reserved for future expansion.
} DRIVERSTATUS, *PDRIVERSTATUS, *LPDRIVERSTATUS;
// Structure returned by PhysicalDrive IOCTL for several commands
typedef struct _SENDCMDOUTPARAMS
{
DWORD cBufferSize; // Size of bBuffer in bytes
DRIVERSTATUS DriverStatus; // Driver status structure.
BYTE bBuffer[1]; // Buffer of arbitrary length in which to store the data read from the // drive.
} SENDCMDOUTPARAMS, *PSENDCMDOUTPARAMS, *LPSENDCMDOUTPARAMS;
// The following struct defines the interesting part of the IDENTIFY
// buffer:
typedef struct _IDSECTOR
{
USHORT wGenConfig;
USHORT wNumCyls;
USHORT wReserved;
USHORT wNumHeads;
USHORT wBytesPerTrack;
USHORT wBytesPerSector;
USHORT wSectorsPerTrack;
USHORT wVendorUnique[3];
CHAR sSerialNumber[20];
USHORT wBufferType;
USHORT wBufferSize;
USHORT wECCSize;
CHAR sFirmwareRev[8];
CHAR sModelNumber[40];
USHORT wMoreVendorUnique;
USHORT wDoubleWordIO;
USHORT wCapabilities;
USHORT wReserved1;
USHORT wPIOTiming;
USHORT wDMATiming;
USHORT wBS;
USHORT wNumCurrentCyls;
USHORT wNumCurrentHeads;
USHORT wNumCurrentSectorsPerTrack;
ULONG ulCurrentSectorCapacity;
USHORT wMultSectorStuff;
ULONG ulTotalAddressableSectors;
USHORT wSingleWordDMA;
USHORT wMultiWordDMA;
BYTE bReserved[128];
} IDSECTOR, *PIDSECTOR;
typedef struct _SRB_IO_CONTROL
{
ULONG HeaderLength;
UCHAR Signature[8];
ULONG Timeout;
ULONG ControlCode;
ULONG ReturnCode;
ULONG Length;
} SRB_IO_CONTROL, *PSRB_IO_CONTROL;
// Define global buffers.
BYTE IdOutCmd [sizeof (SENDCMDOUTPARAMS) + IDENTIFY_BUFFER_SIZE - 1];
char *ConvertToString (DWORD diskdata [256], int firstIndex, int lastIndex);
void PrintIdeInfo (int drive, DWORD diskdata [256]);
BOOL DoIDENTIFY (HANDLE, PSENDCMDINPARAMS, PSENDCMDOUTPARAMS, BYTE, BYTE,
PDWORD);
int ReadPhysicalDriveInNT (void)
{
int done = FALSE;
int drive = 0;
for (drive = 0; drive < MAX_IDE_DRIVES; drive++)
{
HANDLE hPhysicalDriveIOCTL = 0;
// Try to get a handle to PhysicalDrive IOCTL, report failure
// and exit if can't.
char driveName [256];
sprintf (driveName, "\\\\.\\PhysicalDrive%d", drive);
// Windows NT, Windows 2000, must have admin rights
hPhysicalDriveIOCTL = CreateFile (driveName,
GENERIC_READ | GENERIC_WRITE,
FILE_SHARE_READ | FILE_SHARE_WRITE, NULL,
OPEN_EXISTING, 0, NULL);
// if (hPhysicalDriveIOCTL == INVALID_HANDLE_VALUE)
// printf ("Unable to open physical drive %d, error code: 0x%lX\n",
// drive, GetLastError ());
if (hPhysicalDriveIOCTL != INVALID_HANDLE_VALUE)
{
GETVERSIONOUTPARAMS VersionParams;
DWORD cbBytesReturned = 0;
// Get the version, etc of PhysicalDrive IOCTL
memset ((void*) &VersionParams, 0, sizeof(VersionParams));
if ( ! DeviceIoControl (hPhysicalDriveIOCTL, DFP_GET_VERSION,
NULL,
0,
&VersionParams,
sizeof(VersionParams),
&cbBytesReturned, NULL) )
{
// printf ("DFP_GET_VERSION failed for drive %d\n", i);
// continue;
}
// If there is a IDE device at number "i" issue commands
// to the device
if (VersionParams.bIDEDeviceMap > 0)
{
BYTE bIDCmd = 0; // IDE or ATAPI IDENTIFY cmd
SENDCMDINPARAMS scip;
//SENDCMDOUTPARAMS OutCmd;
// Now, get the ID sector for all IDE devices in the system.
// If the device is ATAPI use the IDE_ATAPI_IDENTIFY command,
// otherwise use the IDE_ATA_IDENTIFY command
bIDCmd = (VersionParams.bIDEDeviceMap >> drive & 0x10) ? \
IDE_ATAPI_IDENTIFY : IDE_ATA_IDENTIFY;
memset (&scip, 0, sizeof(scip));
memset (IdOutCmd, 0, sizeof(IdOutCmd));
if ( DoIDENTIFY (hPhysicalDriveIOCTL,
&scip,
(PSENDCMDOUTPARAMS)&IdOutCmd,
(BYTE) bIDCmd,
(BYTE) drive,
&cbBytesReturned))
{
DWORD diskdata [256];
int ijk = 0;
USHORT *pIdSector = (USHORT *)
((PSENDCMDOUTPARAMS) IdOutCmd) -> bBuffer;
for (ijk = 0; ijk < 256; ijk++)
diskdata [ijk] = pIdSector [ijk];
PrintIdeInfo (drive, diskdata);
done = TRUE;
}
}
CloseHandle (hPhysicalDriveIOCTL);
}
}
return done;
}
// DoIDENTIFY
// FUNCTION: Send an IDENTIFY command to the drive
// bDriveNum = 0-3
// bIDCmd = IDE_ATA_IDENTIFY or IDE_ATAPI_IDENTIFY
BOOL DoIDENTIFY (HANDLE hPhysicalDriveIOCTL, PSENDCMDINPARAMS pSCIP,
PSENDCMDOUTPARAMS pSCOP, BYTE bIDCmd, BYTE bDriveNum,
PDWORD lpcbBytesReturned)
{
// Set up data structures for IDENTIFY command.
pSCIP -> cBufferSize = IDENTIFY_BUFFER_SIZE;
pSCIP -> irDriveRegs.bFeaturesReg = 0;
pSCIP -> irDriveRegs.bSectorCountReg = 1;
pSCIP -> irDriveRegs.bSectorNumberReg = 1;
pSCIP -> irDriveRegs.bCylLowReg = 0;
pSCIP -> irDriveRegs.bCylHighReg = 0;
// Compute the drive number.
pSCIP -> irDriveRegs.bDriveHeadReg = 0xA0 | ((bDriveNum & 1) << 4);
// The command can either be IDE identify or ATAPI identify.
pSCIP -> irDriveRegs.bCommandReg = bIDCmd;
pSCIP -> bDriveNumber = bDriveNum;
pSCIP -> cBufferSize = IDENTIFY_BUFFER_SIZE;
return ( DeviceIoControl (hPhysicalDriveIOCTL, DFP_RECEIVE_DRIVE_DATA,
(LPVOID) pSCIP,
sizeof(SENDCMDINPARAMS) - 1,
(LPVOID) pSCOP,
sizeof(SENDCMDOUTPARAMS) + IDENTIFY_BUFFER_SIZE - 1,
lpcbBytesReturned, NULL) );
}
// ------------------------------------------------- //
// WinIo v1.2 //
// Direct Hardware Access Under Windows 9x/NT/2000 //
// Copyright 1998-2000 Yariv Kaplan //
// http://www.internals.com //
// ------------------------------------------------- //
//#include <windows.h>
//#include "instdrv.h"
BOOL LoadDeviceDriver( const TCHAR * Name, const TCHAR * Path, HANDLE * lphDevice );
BOOL UnloadDeviceDriver( const TCHAR * Name );
HANDLE hDriver;
bool IsNT;
bool IsWinIoInitialized = false;
bool IsWinNT()
{
OSVERSIONINFO OSVersionInfo;
OSVersionInfo.dwOSVersionInfoSize = sizeof(OSVERSIONINFO);
GetVersionEx(&OSVersionInfo);
return OSVersionInfo.dwPlatformId == VER_PLATFORM_WIN32_NT;
}
bool InitializeWinIo()
{
char szExePath[MAX_PATH];
PSTR pszSlash;
IsNT = IsWinNT();
if (IsNT)
{
if (!GetModuleFileName(GetModuleHandle(NULL), szExePath, sizeof(szExePath)))
return false;
pszSlash = strrchr(szExePath, '\\');
if (pszSlash)
pszSlash[1] = 0;
else
return false;
strcat(szExePath, "winio.sys");
// UnloadDeviceDriver("WINIO");
// if (!LoadDeviceDriver("WINIO", szExePath, &hDriver))
// return false;
}
IsWinIoInitialized = true;
return true;
}
void ShutdownWinIo()
{
// if (IsNT)
// UnloadDeviceDriver("WINIO");
}
// ------------------------------------------------ //
// Port32 v3.0 //
// Direct Port Access Under Windows 9x/NT/2000 //
// Copyright 1998-2000 Yariv Kaplan //
// http://www.internals.com //
// ------------------------------------------------ //
//#include <windows.h>
#include <winioctl.h>
#include "port32.h"
#include "winio.h"
//#include "general.h"
// These are our ring 0 functions responsible for tinkering with the hardware ports.
// They have a similar privilege to a Windows VxD and are therefore free to access
// protected system resources (such as the page tables) and even place calls to
// exported VxD services.
__declspec(naked) void Ring0GetPortVal()
{
_asm
{
Cmp CL, 1
Je ByteVal
Cmp CL, 2
Je WordVal
Cmp CL, 4
Je DWordVal
ByteVal:
In AL, DX
Mov [EBX], AL
Retf
WordVal:
In AX, DX
Mov [EBX], AX
Retf
DWordVal:
In EAX, DX
Mov [EBX], EAX
Retf
}
}
__declspec(naked) void Ring0SetPortVal()
{
_asm
{
Cmp CL, 1
Je ByteVal
Cmp CL, 2
Je WordVal
Cmp CL, 4
Je DWordVal
ByteVal:
Mov AL, [EBX]
Out DX, AL
Retf
WordVal:
Mov AX, [EBX]
Out DX, AX
Retf
DWordVal:
Mov EAX, [EBX]
Out DX, EAX
Retf
}
}
// This function makes it possible to call ring 0 code from a ring 3
// application.
bool CallRing0(PVOID pvRing0FuncAddr, WORD wPortAddr, PDWORD pdwPortVal, BYTE bSize)
{
struct GDT_DESCRIPTOR *pGDTDescriptor;
struct GDTR gdtr;
WORD CallgateAddr[3];
WORD wGDTIndex = 1;
_asm Sgdt [gdtr]
// Skip the null descriptor
pGDTDescriptor = (struct GDT_DESCRIPTOR *)(gdtr.dwGDTBase + 8);
// Search for a free GDT descriptor
for (wGDTIndex = 1; wGDTIndex < (gdtr.wGDTLimit / 8); wGDTIndex++)
{
if (pGDTDescriptor->Type == 0 &&
pGDTDescriptor->System == 0 &&
pGDTDescriptor->DPL == 0 &&
pGDTDescriptor->Present == 0)
{
// Found one !
// Now we need to transform this descriptor into a callgate.
// Note that we're using selector 0x28 since it corresponds
// to a ring 0 segment which spans the entire linear address
// space of the processor (0-4GB).
struct CALLGATE_DESCRIPTOR *pCallgate;
pCallgate = (struct CALLGATE_DESCRIPTOR *) pGDTDescriptor;
pCallgate->Offset_0_15 = LOWORD(pvRing0FuncAddr);
pCallgate->Selector = 0x28;
pCallgate->ParamCount = 0;
pCallgate->Unused = 0;
pCallgate->Type = 0xc;
pCallgate->System = 0;
pCallgate->DPL = 3;
pCallgate->Present = 1;
pCallgate->Offset_16_31 = HIWORD(pvRing0FuncAddr);
// Prepare the far call parameters
CallgateAddr[0] = 0x0;
CallgateAddr[1] = 0x0;
CallgateAddr[2] = (wGDTIndex << 3) | 3;
// Please fasten your seat belts!
// We're about to make a hyperspace jump into RING 0.
_asm Mov DX, [wPortAddr]
_asm Mov EBX, [pdwPortVal]
_asm Mov CL, [bSize]
_asm Call FWORD PTR [CallgateAddr]
// We have made it !
// Now free the GDT descriptor
memset(pGDTDescriptor, 0, 8);
// Our journey was successful. Seeya.
return true;
}
// Advance to the next GDT descriptor
pGDTDescriptor++;
}
// Whoops, the GDT is full
return false;
}
bool GetPortVal(WORD wPortAddr, PDWORD pdwPortVal, BYTE bSize)
{
bool Result;
DWORD dwBytesReturned;
struct tagPort32Struct Port32Struct;
if (IsNT)
{
if (!IsWinIoInitialized)
return false;
Port32Struct.wPortAddr = wPortAddr;
Port32Struct.bSize = bSize;
if (!DeviceIoControl(hDriver, IOCTL_WINIO_READPORT, &Port32Struct,
sizeof(struct tagPort32Struct), &Port32Struct,
sizeof(struct tagPort32Struct),
&dwBytesReturned, NULL))
return false;
else
*pdwPortVal = Port32Struct.dwPortVal;
}
else
{
Result = CallRing0((PVOID)Ring0GetPortVal, wPortAddr, pdwPortVal, bSize);
if (Result == false)
return false;
}
return true;
}
bool SetPortVal(WORD wPortAddr, DWORD dwPortVal, BYTE bSize)
{
DWORD dwBytesReturned;
struct tagPort32Struct Port32Struct;
if (IsNT)
{
if (!IsWinIoInitialized)
return false;
Port32Struct.wPortAddr = wPortAddr;
Port32Struct.dwPortVal = dwPortVal;
Port32Struct.bSize = bSize;
if (!DeviceIoControl(hDriver, IOCTL_WINIO_WRITEPORT, &Port32Struct,
sizeof(struct tagPort32Struct), NULL, 0, &dwBytesReturned, NULL))
return false;
}
else
return CallRing0((PVOID)Ring0SetPortVal, wPortAddr, &dwPortVal, bSize);
return true;
}
int ReadDrivePortsInWin9X (void)
{
int done = FALSE;
int drive = 0;
InitializeWinIo ();
// Get IDE Drive info from the hardware ports
// loop thru all possible drives
for (drive = 0; drive < 8; drive++)
{
DWORD diskdata [256];
WORD baseAddress = 0; // Base address of drive controller
DWORD portValue = 0;
int waitLoop = 0;
int index = 0;
switch (drive / 2)
{
case 0: baseAddress = 0x1f0; break;
case 1: baseAddress = 0x170; break;
case 2: baseAddress = 0x1e8; break;
case 3: baseAddress = 0x168; break;
}
// Wait for controller not busy
waitLoop = 100000;
while (--waitLoop > 0)
{
GetPortVal ((WORD) (baseAddress + 7), &portValue, (BYTE) 1);
// drive is ready
if ((portValue & 0x40) == 0x40) break;
// previous drive command ended in error
if ((portValue & 0x01) == 0x01) break;
}
if (waitLoop < 1) continue;
// Set Master or Slave drive
if ((drive % 2) == 0)
SetPortVal ((WORD) (baseAddress + 6), 0xA0, 1);
else
SetPortVal ((WORD) (baseAddress + 6), 0xB0, 1);
// Get drive info data
SetPortVal ((WORD) (baseAddress + 7), 0xEC, 1);
// Wait for data ready
waitLoop = 100000;
while (--waitLoop > 0)
{
GetPortVal ((WORD) (baseAddress + 7), &portValue, 1);
// see if the drive is ready and has it's info ready for us
if ((portValue & 0x48) == 0x48) break;
// see if there is a drive error
if ((portValue & 0x01) == 0x01) break;
}
// check for time out or other error
if (waitLoop < 1 || portValue & 0x01) continue;
// read drive id information
for (index = 0; index < 256; index++)
{
diskdata [index] = 0; // init the space
GetPortVal (baseAddress, &(diskdata [index]), 2);
}
PrintIdeInfo (drive, diskdata);
done = TRUE;
}
ShutdownWinIo ();
return done;
}
#define SENDIDLENGTH sizeof (SENDCMDOUTPARAMS) + IDENTIFY_BUFFER_SIZE
int ReadIdeDriveAsScsiDriveInNT (void)
{
int done = FALSE;
int controller = 0;
for (controller = 0; controller < 2; controller++)
{
HANDLE hScsiDriveIOCTL = 0;
char driveName [256];
// Try to get a handle to PhysicalDrive IOCTL, report failure
// and exit if can't.
sprintf (driveName, "\\\\.\\Scsi%d:", controller);
// Windows NT, Windows 2000, any rights should do
hScsiDriveIOCTL = CreateFile (driveName,
GENERIC_READ | GENERIC_WRITE,
FILE_SHARE_READ | FILE_SHARE_WRITE, NULL,
OPEN_EXISTING, 0, NULL);
// if (hScsiDriveIOCTL == INVALID_HANDLE_VALUE)
// printf ("Unable to open SCSI controller %d, error code: 0x%lX\n",
// controller, GetLastError ());
if (hScsiDriveIOCTL != INVALID_HANDLE_VALUE)
{
int drive = 0;
for (drive = 0; drive < 2; drive++)
{
char buffer [sizeof (SRB_IO_CONTROL) + SENDIDLENGTH];
SRB_IO_CONTROL *p = (SRB_IO_CONTROL *) buffer;
SENDCMDINPARAMS *pin =
(SENDCMDINPARAMS *) (buffer + sizeof (SRB_IO_CONTROL));
DWORD dummy;
memset (buffer, 0, sizeof (buffer));
p -> HeaderLength = sizeof (SRB_IO_CONTROL);
p -> Timeout = 10000;
p -> Length = SENDIDLENGTH;
p -> ControlCode = IOCTL_SCSI_MINIPORT_IDENTIFY;
strncpy ((char *) p -> Signature, "SCSIDISK", 8);
pin -> irDriveRegs.bCommandReg = IDE_ATA_IDENTIFY;
pin -> bDriveNumber = drive;
if (DeviceIoControl (hScsiDriveIOCTL, IOCTL_SCSI_MINIPORT,
buffer,
sizeof (SRB_IO_CONTROL) +
sizeof (SENDCMDINPARAMS) - 1,
buffer,
sizeof (SRB_IO_CONTROL) + SENDIDLENGTH,
&dummy, NULL))
{
SENDCMDOUTPARAMS *pOut =
(SENDCMDOUTPARAMS *) (buffer + sizeof (SRB_IO_CONTROL));
IDSECTOR *pId = (IDSECTOR *) (pOut -> bBuffer);
if (pId -> sModelNumber [0])
{
DWORD diskdata [256];
int ijk = 0;
USHORT *pIdSector = (USHORT *) pId;
for (ijk = 0; ijk < 256; ijk++)
diskdata [ijk] = pIdSector [ijk];
PrintIdeInfo (controller * 2 + drive, diskdata);
done = TRUE;
}
}
}
CloseHandle (hScsiDriveIOCTL);
}
}
return done;
}
char HardDriveSerialNumber [1024];
void PrintIdeInfo (int drive, DWORD diskdata [256])
{
// copy the hard driver serial number to the buffer
strcpy (HardDriveSerialNumber, ConvertToString (diskdata, 10, 19));
#ifdef PRINTING_TO_CONSOLE_ALLOWED
switch (drive / 2)
{
case 0: printf ("\nPrimary Controller - ");
break;
case 1: printf ("\nSecondary Controller - ");
break;
case 2: printf ("\nTertiary Controller - ");
break;
case 3: printf ("\nQuaternary Controller - ");
break;
}
switch (drive % 2)
{
case 0: printf ("Master drive\n\n");
break;
case 1: printf ("Slave drive\n\n");
break;
}
printf ("Drive Model Number________________: %s\n",
ConvertToString (diskdata, 27, 46));
printf ("Drive Serial Number_______________: %s\n",
ConvertToString (diskdata, 10, 19));
printf ("Drive Controller Revision Number__: %s\n",
ConvertToString (diskdata, 23, 26));
printf ("Controller Buffer Size on Drive___: %u bytes\n",
diskdata [21] * 512);
printf ("Drive Type________________________: ");
if (diskdata [0] & 0x0080)
printf ("Removable\n");
else if (diskdata [0] & 0x0040)
printf ("Fixed\n");
else printf ("Unknown\n");
printf ("Physical Geometry: "
"%u Cylinders %u Heads %u Sectors per track\n",
diskdata [1], diskdata [3], diskdata [6]);
#else // PRINTING_TO_CONSOLE_ALLOWED
// nothing to do
#endif // PRINTING_TO_CONSOLE_ALLOWED
}
char *ConvertToString (DWORD diskdata [256], int firstIndex, int lastIndex)
{
static char string [1024];
int index = 0;
int position = 0;
// each integer has two characters stored in it backwards
for (index = firstIndex; index <= lastIndex; index++)
{
// get high byte for 1st character
string [position] = (char) (diskdata [index] / 256);
position++;
// get low byte for 2nd character
string [position] = (char) (diskdata [index] % 256);
position++;
}
// end the string
string [position] = '\0';
// cut off the trailing blanks
for (index = position - 1; index > 0 && ' ' == string [index]; index--)
string [index] = '\0';
return string;
}
long getHardDriveComputerID ()
{
int done = FALSE;
//char string [1024];
__int64 id = 0;
strcpy (HardDriveSerialNumber, "");
// this works under WinNT4 or Win2K if you have admin rights
done = ReadPhysicalDriveInNT (); //FUNCION LISTA
// this should work in WinNT or Win2K if previous did not work
// this is kind of a backdoor via the SCSI mini port driver into
// the IDE drives
if ( ! done) done = ReadIdeDriveAsScsiDriveInNT (); //FUNCION LISTA
// this works under Win9X and calls WINIO.DLL
if ( ! done) done = ReadDrivePortsInWin9X ();
if (done)
{
char *p = HardDriveSerialNumber;
//WriteConstantString ("HardDriveSerialNumber", HardDriveSerialNumber);
// ignore first 5 characters from western digital hard drives if
// the first four characters are WD-W
if ( ! strncmp (HardDriveSerialNumber, "WD-W", 4)) p += 5;
for ( ; p && *p; p++)
{
if ('-' == *p) continue;
id *= 10;
switch (*p)
{
case '0': id += 0; break;
case '1': id += 1; break;
case '2': id += 2; break;
case '3': id += 3; break;
case '4': id += 4; break;
case '5': id += 5; break;
case '6': id += 6; break;
case '7': id += 7; break;
case '8': id += 8; break;
case '9': id += 9; break;
case 'a': case 'A': id += 10; break;
case 'b': case 'B': id += 11; break;
case 'c': case 'C': id += 12; break;
case 'd': case 'D': id += 13; break;
case 'e': case 'E': id += 14; break;
case 'f': case 'F': id += 15; break;
case 'g': case 'G': id += 16; break;
case 'h': case 'H': id += 17; break;
case 'i': case 'I': id += 18; break;
case 'j': case 'J': id += 19; break;
case 'k': case 'K': id += 20; break;
case 'l': case 'L': id += 21; break;
case 'm': case 'M': id += 22; break;
case 'n': case 'N': id += 23; break;
case 'o': case 'O': id += 24; break;
case 'p': case 'P': id += 25; break;
case 'q': case 'Q': id += 26; break;
case 'r': case 'R': id += 27; break;
case 's': case 'S': id += 28; break;
case 't': case 'T': id += 29; break;
case 'u': case 'U': id += 30; break;
case 'v': case 'V': id += 31; break;
case 'w': case 'W': id += 32; break;
case 'x': case 'X': id += 33; break;
case 'y': case 'Y': id += 34; break;
case 'z': case 'Z': id += 35; break;
}
}
}
// make sure no bigger than 16^7
if (id > 268435455) id %= 268435456;
#ifdef PRINTING_TO_CONSOLE_ALLOWED
printf ("\nComputer ID_______________________: %d\n", id);
#endif
return (long) id;
}
int main (int argc, char * argv [])
{
long id = getHardDriveComputerID ();
return 0;
}
|
Este codigo, es para Visual C, donde funciona de maravilla, pero, no se pude ejecutar, muy bien que digamos, asi mismo tengo la siguiente funcion espero que tambien se le haga mas facil, ya que no he podido hacer que jale en win9x Y Me.. de antemano les agradesco mucho...
Pido tambien disculpas al creador de la funcion, ya que esta la encontre en una pagina japones, donde viene el codigo, pero creo que no trabajan, mucho sobre builder y el japones, no lo hablo tan fluido, espero me ayuden y si la funcion les sirve bueno, pues aqui estan
| Código: |
#include <windows.h>
#include <iostream.h>
#include <stdio.h>
#define DFP_GET_VERSION 0x00074080
#define DFP_SEND_DRIVE_COMMAND 0x0007c084
#define DFP_RECEIVE_DRIVE_DATA 0x0007c088
#pragma pack(1)
typedef struct _GETVERSIONOUTPARAMS {
BYTE bVersion; // Binary driver version.
BYTE bRevision; // Binary driver revision.
BYTE bReserved; // Not used.
BYTE bIDEDeviceMap; // Bit map of IDE devices.
DWORD fCapabilities; // Bit mask of driver capabilities.
DWORD dwReserved[4]; // For future use.
} GETVERSIONOUTPARAMS, *PGETVERSIONOUTPARAMS, *LPGETVERSIONOUTPARAMS;
typedef struct _IDEREGS {
BYTE bFeaturesReg; // Used for specifying SMART "commands".
BYTE bSectorCountReg; // IDE sector count register
BYTE bSectorNumberReg; // IDE sector number register
BYTE bCylLowReg; // IDE low order cylinder value
BYTE bCylHighReg; // IDE high order cylinder value
BYTE bDriveHeadReg; // IDE drive/head register
BYTE bCommandReg; // Actual IDE command.
BYTE bReserved; // reserved for future use. Must be zero.
} IDEREGS, *PIDEREGS, *LPIDEREGS;
typedef struct _SENDCMDINPARAMS {
DWORD cBufferSize; // Buffer size in bytes
IDEREGS irDriveRegs; // Structure with drive register values.
BYTE bDriveNumber; // Physical drive number to send
// command to (0,1,2,3).
BYTE bReserved[3]; // Reserved for future expansion.
DWORD dwReserved[4]; // For future use.
//BYTE bBuffer[1]; // Input buffer.
} SENDCMDINPARAMS, *PSENDCMDINPARAMS, *LPSENDCMDINPARAMS;
typedef struct _DRIVERSTATUS {
BYTE bDriverError; // Error code from driver,
// or 0 if no error.
BYTE bIDEStatus; // Contents of IDE Error register.
// Only valid when bDriverError
// is SMART_IDE_ERROR.
BYTE bReserved[2]; // Reserved for future expansion.
DWORD dwReserved[2]; // Reserved for future expansion.
} DRIVERSTATUS, *PDRIVERSTATUS, *LPDRIVERSTATUS;
typedef struct _SENDCMDOUTPARAMS {
DWORD cBufferSize; // Size of bBuffer in bytes
DRIVERSTATUS DriverStatus; // Driver status structure.
BYTE bBuffer[512]; // Buffer of arbitrary length
// in which to store the data read from the drive.
} SENDCMDOUTPARAMS, *PSENDCMDOUTPARAMS, *LPSENDCMDOUTPARAMS;
typedef struct _IDSECTOR {
USHORT wGenConfig;
USHORT wNumCyls;
USHORT wReserved;
USHORT wNumHeads;
USHORT wBytesPerTrack;
USHORT wBytesPerSector;
USHORT wSectorsPerTrack;
USHORT wVendorUnique[3];
CHAR sSerialNumber[20];
USHORT wBufferType;
USHORT wBufferSize;
USHORT wECCSize;
CHAR sFirmwareRev[8];
CHAR sModelNumber[40];
USHORT wMoreVendorUnique;
USHORT wDoubleWordIO;
USHORT wCapabilities;
USHORT wReserved1;
USHORT wPIOTiming;
USHORT wDMATiming;
USHORT wBS;
USHORT wNumCurrentCyls;
USHORT wNumCurrentHeads;
USHORT wNumCurrentSectorsPerTrack;
ULONG ulCurrentSectorCapacity;
USHORT wMultSectorStuff;
ULONG ulTotalAddressableSectors;
USHORT wSingleWordDMA;
USHORT wMultiWordDMA;
BYTE bReserved[128];
} IDSECTOR, *PIDSECTOR;
/*+++
Global vars
---*/
GETVERSIONOUTPARAMS vers;
SENDCMDINPARAMS in;
SENDCMDOUTPARAMS out;
HANDLE h;
DWORD i;
BYTE j;
void CopyRight(){
cerr<<endl<<"HDD identifier v1.0 for WIN95/98/Me/NT/2000. written by Lu Lin"<<endl;
cerr<<"For more information, please visit Inside Programming: http://lu0.126.com"<<endl;
cerr<<"2000.11.3"<<endl<<endl;
}
VOID ChangeByteOrder(PCHAR szString, USHORT uscStrSize)
{
USHORT i;
CHAR temp;
for (i = 0; i < uscStrSize; i+=2)
{
temp = szString[i];
szString[i] = szString[i+1];
szString[i+1] = temp;
}
}
void DetectIDE(BYTE bIDEDeviceMap){
if (bIDEDeviceMap&1){
if (bIDEDeviceMap&16){
cout<<"ATAPI device is attached to primary controller, drive 0."<<endl;
}else{
cout<<"IDE device is attached to primary controller, drive 0."<<endl;
}
}
if (bIDEDeviceMap&2){
if (bIDEDeviceMap&32){
cout<<"ATAPI device is attached to primary controller, drive 1."<<endl;
}else{
cout<<"IDE device is attached to primary controller, drive 1."<<endl;
}
}
if (bIDEDeviceMap&4){
if (bIDEDeviceMap&64){
cout<<"ATAPI device is attached to secondary controller, drive 0."<<endl;
}else{
cout<<"IDE device is attached to secondary controller, drive 0."<<endl;
}
}
if (bIDEDeviceMap&8){
if (bIDEDeviceMap&128){
cout<<"ATAPI device is attached to secondary controller, drive 1."<<endl;
}else{
cout<<"IDE device is attached to secondary controller, drive 1."<<endl;
}
}
}
void hdid9x(){
ZeroMemory(&vers,sizeof(vers));
//We start in 95/98/Me
h=CreateFile("\\\\.\\Smartvsd",0,0,0,CREATE_NEW,0,0);
if (!h){
cout<<"open smartvsd.vxd failed"<<endl;
exit(0);
}
if (!DeviceIoControl(h,DFP_GET_VERSION,0,0,&vers,sizeof(vers),&i,0)){
cout<<"DeviceIoControl failed:DFP_GET_VERSION"<<endl;
CloseHandle(h);
return;
}
//If IDE identify command not supported, fails
if (!(vers.fCapabilities&1)){
cout<<"Error: IDE identify command not supported.";
CloseHandle(h);
return;
}
//Display IDE drive number detected
DetectIDE(vers.bIDEDeviceMap);
//Identify the IDE drives
for (j=0;j<4;j++){
PIDSECTOR phdinfo;
char s[41];
ZeroMemory(&in,sizeof(in));
ZeroMemory(&out,sizeof(out));
if (j&1){
in.irDriveRegs.bDriveHeadReg=0xb0;
}else{
in.irDriveRegs.bDriveHeadReg=0xa0;
}
if (vers.fCapabilities&(16>>j)){
//We don't detect a ATAPI device.
cout<<"Drive "<<(int)(j+1)<<" is a ATAPI device, we don't detect it"<<endl;
continue;
}else{
in.irDriveRegs.bCommandReg=0xec;
}
in.bDriveNumber=j;
in.irDriveRegs.bSectorCountReg=1;
in.irDriveRegs.bSectorNumberReg=1;
in.cBufferSize=512;
if (!DeviceIoControl(h,DFP_RECEIVE_DRIVE_DATA,&in,sizeof(in),&out,sizeof(out),&i,0)){
cout<<"DeviceIoControl failed:DFP_RECEIVE_DRIVE_DATA"<<endl;
CloseHandle(h);
return;
}
phdinfo=(PIDSECTOR)out.bBuffer;
memcpy(s,phdinfo->sModelNumber,40);
s[40]=0;
ChangeByteOrder(s,40);
cout<<endl<<"Module Number:"<<s<<endl;
memcpy(s,phdinfo->sFirmwareRev,8);
s[8]=0;
ChangeByteOrder(s,8);
cout<<"\tFirmware rev:"<<s<<endl;
memcpy(s,phdinfo->sSerialNumber,20);
s[20]=0;
ChangeByteOrder(s,20);
cout<<"\tSerial Number:"<<s<<endl;
cout<<"\tCapacity:"<<phdinfo->ulTotalAddressableSectors/2/1024<<"M"<<endl<<endl;
}
//Close handle before quit
CloseHandle(h);
CopyRight();
}
void hdidnt(){
char hd[80];
PIDSECTOR phdinfo;
char s[41];
ZeroMemory(&vers,sizeof(vers));
//We start in NT/Win2000
for (j=0;j<4;j++){
sprintf(hd,"\\\\.\\PhysicalDrive%d",j);
h=CreateFile(hd,GENERIC_READ|GENERIC_WRITE,
FILE_SHARE_READ|FILE_SHARE_WRITE,0,OPEN_EXISTING,0,0);
if (!h){
continue;
}
if (!DeviceIoControl(h,DFP_GET_VERSION,0,0,&vers,sizeof(vers),&i,0)){
CloseHandle(h);
continue;
}
//If IDE identify command not supported, fails
if (!(vers.fCapabilities&1)){
cout<<"Error: IDE identify command not supported.";
CloseHandle(h);
return;
}
//Identify the IDE drives
ZeroMemory(&in,sizeof(in));
ZeroMemory(&out,sizeof(out));
if (j&1){
in.irDriveRegs.bDriveHeadReg=0xb0;
}else{
in.irDriveRegs.bDriveHeadReg=0xa0;
}
if (vers.fCapabilities&(16>>j)){
//We don't detect a ATAPI device.
cout<<"Drive "<<(int)(j+1)<<" is a ATAPI device, we don't detect it"<<endl;
continue;
}else{
in.irDriveRegs.bCommandReg=0xec;
}
in.bDriveNumber=j;
in.irDriveRegs.bSectorCountReg=1;
in.irDriveRegs.bSectorNumberReg=1;
in.cBufferSize=512;
if (!DeviceIoControl(h,DFP_RECEIVE_DRIVE_DATA,&in,sizeof(in),&out,sizeof(out),&i,0)){
cout<<"DeviceIoControl failed:DFP_RECEIVE_DRIVE_DATA"<<endl;
CloseHandle(h);
return;
}
phdinfo=(PIDSECTOR)out.bBuffer;
memcpy(s,phdinfo->sModelNumber,40);
s[40]=0;
ChangeByteOrder(s,40);
cout<<endl<<"Module Number:"<<s<<endl;
memcpy(s,phdinfo->sFirmwareRev,8);
s[8]=0;
ChangeByteOrder(s,8);
cout<<"\tFirmware rev:"<<s<<endl;
memcpy(s,phdinfo->sSerialNumber,20);
s[20]=0;
ChangeByteOrder(s,20);
cout<<"\tSerial Number:"<<s<<endl;
cout<<"\tCapacity:"<<phdinfo->ulTotalAddressableSectors/2/1024<<"M"<<endl<<endl;
CloseHandle(h);
}
CopyRight();
}
void main(){
OSVERSIONINFO VersionInfo;
ZeroMemory(&VersionInfo,sizeof(VersionInfo));
VersionInfo.dwOSVersionInfoSize=sizeof(VersionInfo);
GetVersionEx(&VersionInfo);
switch (VersionInfo.dwPlatformId){
case VER_PLATFORM_WIN32s:
cout<<"Win32s is not supported by this programm."<<endl;
return;
case VER_PLATFORM_WIN32_WINDOWS:
hdid9x();
return;
case VER_PLATFORM_WIN32_NT:
hdidnt();
return;
}
}
|
Espero que _Leo o Roberto me puedan ayudar con esto, lo unico que requiero es saber el Serial interno de un Disco duro, ese que aparece al inicial el equipo..
Gracias y Saludos a Todos
_________________
 |
|
FAQ
Buscar
Miembros
Grupos de Usuarios
Registrarse
Perfil
Entra para ver tus mensajes privados
Entrar
